WMsensors.pl is a Perl-based software that monitors CPU and motherboard temperature and voltage. It is a small program designed to keep track of the computer's performance.
Introduction:
If you're someone who always keeps an eye on the temperature and voltage levels of your CPU and motherboard, then WMsensors.pl is the software for you. It is a small perl-program specially designed to monitor the temperature and voltages of CPU and motherboard and also show the fan-speed. The software runs as a dock app for Window Maker.
Features:
WMsensors.pl does not need any config file to function. But, for it to run properly, you need to have a configured installation of lm_sensors. The software uses the Wharf::JDockApp module from the CPAN. It displays the temperature and voltage levels in an easy-to-understand format.
Requirements:
To use WMsensors.pl, you must have a properly configured installation of lm_sensors. You can check if you have correctly installed lm_sensors by running the command "sensors." The output of the command should contain lines such as the ones below:
• CPU core: +1.87 V (min = +1.98 V, max = +2.49 V) ALARM
• +2.5V: +0.36 V (min = +2.24 V, max = +2.74 V) ALARM
• I/O: +3.40 V (min = +2.95 V, max = +3.62 V)
• +5V: +4.89 V (min = +4.47 V, max = +5.49 V)
• +12V: +12.04 V (min = +10.79 V, max = +13.18 V)
• CPU Fan: 0 RPM (min = 3000 RPM, div = 2)
• P/S Fan: 0 RPM (min = 3000 RPM, div = 2)
• SYS Temp: +34.4C (limit = +45C, hysteresis = +40C)
• CPU Temp: +40.3C (limit = +60C, hysteresis = +55C)
• SBr Temp: +24.8C (limit = +65C, hysteresis = +60C)
Installation:
To install and run WMsensors.pl, follow these steps:
Step 1: Make sure you have installed the Perl module "Wharf::JDockApp" from the CPAN. If you have not installed this module, type the following command on the shell:
$ perl -MCPAN -e 'install Wharf::JDockApp'
This command will install the necessary Perl-module.
Step 2: Copy "wmsensors.pl" to "/usr/local/bin".
Step 3: Run wmsensors.pl using either of the following commands:
$ wmsensors.pl
or
$ wmsensors.pl --help
Conclusion:
In conclusion, WMsensors.pl is a great software for those who want to keep a constant check on their CPU and motherboard's temperature and voltage levels. It is a small, easy-to-understand, and reliable program that runs as a dock app for Window Maker. The software does not require any config files and is easy to install and use.
If you're someone who always keeps an eye on the temperature and voltage levels of your CPU and motherboard, then WMsensors.pl is the software for you. It is a small perl-program specially designed to monitor the temperature and voltages of CPU and motherboard and also show the fan-speed. The software runs as a dock app for Window Maker.
Features:
WMsensors.pl does not need any config file to function. But, for it to run properly, you need to have a configured installation of lm_sensors. The software uses the Wharf::JDockApp module from the CPAN. It displays the temperature and voltage levels in an easy-to-understand format.
Requirements:
To use WMsensors.pl, you must have a properly configured installation of lm_sensors. You can check if you have correctly installed lm_sensors by running the command "sensors." The output of the command should contain lines such as the ones below:
• CPU core: +1.87 V (min = +1.98 V, max = +2.49 V) ALARM
• +2.5V: +0.36 V (min = +2.24 V, max = +2.74 V) ALARM
• I/O: +3.40 V (min = +2.95 V, max = +3.62 V)
• +5V: +4.89 V (min = +4.47 V, max = +5.49 V)
• +12V: +12.04 V (min = +10.79 V, max = +13.18 V)
• CPU Fan: 0 RPM (min = 3000 RPM, div = 2)
• P/S Fan: 0 RPM (min = 3000 RPM, div = 2)
• SYS Temp: +34.4C (limit = +45C, hysteresis = +40C)
• CPU Temp: +40.3C (limit = +60C, hysteresis = +55C)
• SBr Temp: +24.8C (limit = +65C, hysteresis = +60C)
Installation:
To install and run WMsensors.pl, follow these steps:
Step 1: Make sure you have installed the Perl module "Wharf::JDockApp" from the CPAN. If you have not installed this module, type the following command on the shell:
$ perl -MCPAN -e 'install Wharf::JDockApp'
This command will install the necessary Perl-module.
Step 2: Copy "wmsensors.pl" to "/usr/local/bin".
Step 3: Run wmsensors.pl using either of the following commands:
$ wmsensors.pl
or
$ wmsensors.pl --help
Conclusion:
In conclusion, WMsensors.pl is a great software for those who want to keep a constant check on their CPU and motherboard's temperature and voltage levels. It is a small, easy-to-understand, and reliable program that runs as a dock app for Window Maker. The software does not require any config files and is easy to install and use.
What's New
Version 0.1: N/A